Smart Elevator Tech, LLC
  • Home
  • Our Products
    • Retracta Ladder
    • Extended Retracta Ladder
    • Pull Pin Pole for Retracta Ladder
    • Overhead Retracta Ladder
    • Divider Beam Kit
    • Powered Retracta Ladder
    • Adjusta Ladder
    • Low-Profile Fishplate
    • Seismic Fish Plates for Old Otis Rails
    • Rope Align Block
  • Contact
  • Ordering & Payment
  • Ordering Guides - RFQs
    • Retracta Ladder Order Form
    • Adjusta Ladder Order Form
  • About Us

​Divider Beam Kit™

 Fully engineered, bolt-in-place clamp-on kit for mount Smart Elevator Tech ladders to hoistway divider beams.
​
Picture
  • Complete kit to mount to divider beams Smart Elevator Tech, LLC ladders including:
               SmartLadder™
               Retracta Ladder®
                Adjusta Ladder™
  • The Divider Beam Kit™ (DBK) can support one (1) ladder or two (2) ladders back-to-back.
  • Can accommodate divider beams 3¼” to 6” wide and up to 10” high.
  • Divider beams may be HSS (tube steel) or I-beam (standard or wide flange).
  • Divider beam top-of-steel (TOS) may be from 6” above to 12” below the elevator sill.
  • DBK includes all hardware and fasteners needed for mounting two (2) ladders, except concrete screws for bottom ladder bracket floor anchorage.
  • DBK must be ordered with ladder(s), as modifications to ladder(s) are included.
  • Standard kit for two-section ladders and Double kit for three-section ladders.
  • Meets ASME A17.1/CSA B44. 
  • Quantities in stock, ready to ship.
  • Made with pride in the USA.

Field labor is typically the most expensive element of new elevator installation.  Field ordering, designing and fabricating custom support components to mount ladders to divider beams can consume expensive time and materials.  Having a simple, easy to install kit in a box, delivered with the Smart Elevator Tech, LLC ladder(s) will save considerable cost and effort.  

The Divider Beam Kit™​ from Smart Elevator Tech, LLC will work with virtually any bottom landing level divider beam size or location.  The DBK should be installed prior to the installation of the pit divider screening or the screening may require modifications to accommodate the DBK.  

Call Smart Elevator Tech, LLC if you have any questions:  415-819-5744

​Download a PDF Flier for the Divider Beam Kit
Divider Beam Kit
File Size: 182 kb
File Type: pdf
Download File

Download a Installation Steps Drawing for mounting an Adjusta Ladder on a DBK
Adjusta Ladder on a DBK
File Size: 229 kb
File Type: pdf
Download File

Download a Installation Steps Drawing for mounting a Retracta Ladder on a DBK
Retracta Ladder on a DBK
File Size: 194 kb
File Type: pdf
Download File

Home

Our Products

Contact

Ordering & Payment


​A Women-Owned Small Business Concern                                                                                                                                                                     Copyright Smart Elevator Tech, LLC 2023
  • Home
  • Our Products
    • Retracta Ladder
    • Extended Retracta Ladder
    • Pull Pin Pole for Retracta Ladder
    • Overhead Retracta Ladder
    • Divider Beam Kit
    • Powered Retracta Ladder
    • Adjusta Ladder
    • Low-Profile Fishplate
    • Seismic Fish Plates for Old Otis Rails
    • Rope Align Block
  • Contact
  • Ordering & Payment
  • Ordering Guides - RFQs
    • Retracta Ladder Order Form
    • Adjusta Ladder Order Form
  • About Us